LDLC Notebook Media 15.4" FR - Pentium M 1.73 GHz 1 Go 80 Go 15.4" TFT Graveur DVD Wi-Fi G (sans OS)

Log

lspcidebian@debian:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI Express Root Port (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 04)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 04)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 04)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
01:00.0 VGA compatible controller: ATI Technologies Inc M24 1P [[Radeon Mobility X600]]
02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)
02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
02:02.0 Network controller: Texas Instruments ACX 111 54Mbps Wireless Interface
02:04.0 CardBus bridge: ENE Technology Inc CB-710/2/4 Cardbus Controller
02:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller
02:04.2 Class 0805: ENE Technology Inc ENE PCI Secure Digital Card Reader Controller
debian@debian:~$ lspci -n
00:00.0 0600: 8086:2590 (rev 03)
00:01.0 0604: 8086:2591 (rev 03)
00:1d.0 0c03: 8086:2658 (rev 04)
00:1d.1 0c03: 8086:2659 (rev 04)
00:1d.2 0c03: 8086:265a (rev 04)
00:1d.3 0c03: 8086:265b (rev 04)
00:1d.7 0c03: 8086:265c (rev 04)
00:1e.0 0604: 8086:2448 (rev d4)
00:1e.2 0401: 8086:266e (rev 04)
00:1e.3 0703: 8086:266d (rev 04)
00:1f.0 0601: 8086:2641 (rev 04)
00:1f.1 0101: 8086:266f (rev 04)
00:1f.3 0c05: 8086:266a (rev 04)
01:00.0 0300: 1002:3150
02:00.0 0c00: 1106:3044 (rev 80)
02:01.0 0200: 10ec:8169 (rev 10)
02:02.0 0280: 104c:9066
02:04.0 0607: 1524:1411
02:04.1 0501: 1524:0530
02:04.2 0805: 1524:0550
debian@debian:~$ dmesg
Linux version 2.6.16-2-486 (Debian 2.6.16-17) (waldi@debian.org) (gcc version 4.0.4 20060630 (prerelease) (Debian 4.0.3-4)) #1 Sat Jul 15 21:23:01 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffdf000 (usable)
BIOS-e820: 000000003ffe0000 - 000000003fffffc0 (ACPI data)
BIOS-e820: 000000003fffffc0 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
1023MB LOWMEM available.
On node 0 totalpages: 262111
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 258015 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
ACPI: RSDP (v000 INSYDE                                ) @ 0x000e5010
ACPI: RSDT (v001 INSYDE RSDT_000 0x00000100 ABCD 0x00010200) @ 0x3fffb2bb
ACPI: FADT (v001 INSYDE FACP_000 0x00000100 0000 0x00010200) @ 0x3ffffb00
ACPI: MADT (v001 STUPID MAPIC_00 0x30307830 ABCD 0x00010200) @ 0x3ffffb90
ACPI: SSDT (v001  PmRef  Cpu0Ist 0x00003000 INTL 0x20030522) @ 0x3fffb4c7
ACPI: SSDT (v001  PmRef  Cpu0Cst 0x00003001 INTL 0x20030522) @ 0x3fffb2ef
ACPI: DSDT (v001 COMPAL DL7x     0x00000001 INTL 0x02002036) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[[0x00]] lapic_id[[0x00]] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[[0x01]] lapic_id[[0x01]] disabled)
ACPI: LAPIC_NMI (acpi_id[[0x00]] high edge lint[[0x1]])
ACPI: LAPIC_NMI (acpi_id[[0x01]] high edge lint[[0x1]])
ACPI: IOAPIC (id[[0x01]] address[[0xfec00000]] gsi_base[[0]])
IOAPIC[[0]]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bff00000)
Built 1 zonelists
Kernel command line: initrd=initrd.gz boot=casper BOOT_IMAGE=vmlinuz
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1729.355 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
Memory: 1031196k/1048444k available (1484k kernel code, 16680k reserved, 570k | 228k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3466.69 BogoMIPS (lpj=6933390)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
CPU: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 4334k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xea524, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [[PCI0]] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1300-133f claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) may be hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
ACPI: PCI Interrupt Routing Table [[\_SB_.PCI0._PRT]]
ACPI: PCI Interrupt Routing Table [[\_SB_.PCI0.PEGP._PRT]]
ACPI: PCI Interrupt Routing Table [[\_SB_.PCI0.PCIB._PRT]]
ACPI: PCI Interrupt Link [[LNKA]] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [[LNKB]] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [[LNKC]] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [[LNKD]] (IRQs 1 *3 4 5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [[LNKE]] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [[LNKF]] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [[LNKG]] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [[LNKH]] (IRQs 1 3 4 5 6 *7 11 12 14 15)
ACPI: Embedded Controller [[EC0]] (gpe 29) interrupt mode.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
 IO window: c000-dfff
 MEM window: c0000000-cfffffff
 PREFETCH window: 90000000-9fffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
 IO window: 0000a400-0000a4ff
 IO window: 0000a800-0000a8ff
 PREFETCH window: 80000000-81ffffff
 MEM window: b2000000-b3ffffff
PCI: Bridge: 0000:00:1e.0
 IO window: a000-bfff
 MEM window: b0000000-bfffffff
 PREFETCH window: 80000000-8fffffff
ACPI: PCI Interrupt 0000:00:01.0[[A]] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:02:04.0[[A]] -> GSI 16 (level, low) -> IRQ 169
audit: initializing netlink socket (disabled)
audit(1160249374.940:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
ACPI: PCI Interrupt 0000:00:01.0[[A]] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[[0000:00:01.0:pcie00]]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [[PNP0303:PS2K,PNP0f13:PS2M]] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ACPI: PCI Interrupt 0000:00:1e.3[[B]] -> GSI 20 (level, low) -> IRQ 193
ACPI: PCI interrupt for device 0000:00:1e.3 disabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI wakeup devices:
AZAL RP01 RP02 RP03 RP04 USB1 USB2 USB3 USB4 USB7 ELAN MODM
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 228k freed
ACPI: CPU0 (power states: C1[[C1]] C2[[C2]] C3[[C3]] C4[[C3]])
ACPI: Processor [[CPU0]] (supports 8 throttling states)
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:02:01.0[[A]] -> GSI 21 (level, low) -> IRQ 201
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xf0838000, 00:0f:b0:ef:51:b0, IRQ 201
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:02:00.0[[A]] -> GSI 20 (level, low) -> IRQ 193
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[[193]]  MMIO=[[b0040800-b0040fff]]  Max Packet=[[512]]  IR/IT contexts=[[4/8]]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[[A]] -> GSI 18 (level, low) -> IRQ 209
ICH6: chipset revision 4
ICH6: not 100% native mode: will probe irqs later
   ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:DMA
   ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
input: AT Translated Set 2 keyboard as /class/input/input0
hda: SAMSUNG MP0804H, ATA DISK drive
hdb: TSSTcorpCD/DVDW TS-L632B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ieee1394: Host added: ID:BUS[[0-00:1023]]  GUID[[00023f62894002a1]]
ACPI: PCI Interrupt 0000:00:1d.0[[A]] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 217, io base 0x00001200
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hda: max request size: 512KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: unknown partition table
hdb: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:00:1d.1[[B]] -> GSI 19 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 225, io base 0x00001220
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[[C]] -> GSI 18 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 209, io base 0x00001240
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[[D]] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 169, io base 0x00001260
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[[A]] -> GSI 23 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 217, io mem 0x50000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 1-1: device not accepting address 2, error -71
usb 1-1: new low speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: HID 062a:0000 as /class/input/input1
input: USB HID v1.10 Mouse [[HID 062a:0000]] on usb-0000:00:1d.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
loop: loaded (max 8 devices)
Registering unionfs 1.2.0pre
unionfs: debugging is not enabled
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt 0000:00:1e.2[[A]] -> GSI 17 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1e.2 to 64
ts: Compaq touchscreen protocol output
input: PS/2 Mouse as /class/input/input2
intel8x0_measure_ac97_clock: measured 55478 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1e.3[[B]] -> GSI 20 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1e.3 to 64
input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
ACPI: PCI Interrupt 0000:02:04.0[[A]] -> GSI 16 (level, low) -> IRQ 169
Yenta: CardBus bridge found at 0000:02:04.0 [[14c0:0012]]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x89001202, devctl 0x44
Yenta: ISA IRQ mask 0x0cf8, PCI irq 169
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xbfff
cs: IO port probe 0xa000-0xbfff: clean.
pcmcia: parent PCI bridge Memory window: 0xb0000000 - 0xbfffffff
pcmcia: parent PCI bridge Memory window: 0x80000000 - 0x8fffffff
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
Intel 810 + AC97 Audio, version 1.01, 21:45:00 Jul 15 2006
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
mice: PS/2 mouse device common for all mice
hw_random: cannot enable RNG, aborting
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
r8169: eth0: link up
ttyS0: LSR safety check engaged======
ttyS0: LSR safety check engaged======
ttyS1: LSR safety check engaged======
ttyS1: LSR safety check engaged======
ttyS1: LSR safety check engaged======
ttyS0: LSR safety check engaged======
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
psmouse.c: GlidePoint at isa0060/serio4/input0 lost synchronization, throwing 1 bytes away.
psmouse.c: resync failed, issuing reconnect request
debian@debian:~$ cat /proc/cpuinfo
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 6
model           : 13
model name      : Intel(R) Pentium(R) M processor 1.73GHz
stepping        : 8
cpu MHz         : 1729.355
cache size      : 2048 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 2
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat clflush dts acpi mmx fxsr sse sse2 ss tm pbe nx est tm2
bogomips        : 3466.69
glxinfo
lsmoddebian@debian:~$ lsmod
Module                  Size  Used by
ipv6                  218080  8
dm_mod                 48180  0
joydev                  9152  0
mousedev               10688  1
eth1394                18180  0
i810_audio             31124  0
ac97_codec             17164  1 i810_audio
intel_agp              21020  1
agpgart                29360  1 intel_agp
yenta_socket           24076  0
rsrc_nonstatic         12160  1 yenta_socket
pcmcia_core            37392  2 yenta_socket,rsrc_nonstatic
i2c_i801                8076  0
i2c_core               19600  1 i2c_i801
evdev                   8960  1
psmouse                34568  0
tsdev                   7488  0
serio_raw               6660  0
snd_intel8x0m          15628  0
snd_intel8x0           29596  1
snd_ac97_codec         82848  2 snd_intel8x0m,snd_intel8x0
snd_ac97_bus            2304  1 snd_ac97_codec
snd_pcm                74376  3 snd_intel8x0m,snd_intel8x0,snd_ac97_codec
snd_timer              20484  1 snd_pcm
snd                    46336  7 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore               8928  2 i810_audio,snd
snd_page_alloc          9992  3 snd_intel8x0m,snd_intel8x0,snd_pcm
rtc                    11572  0
squashfs               39760  1
unionfs                66464  1
loop                   14216  2
nls_iso8859_1           4224  1
isofs                  32192  1
usbhid                 32352  0
ide_cd                 35488  1
cdrom                  32176  1 ide_cd
ide_disk               14976  0
ehci_hcd               27144  0
uhci_hcd               27152  0
usbcore               111008  4 usbhid,ehci_hcd,uhci_hcd
piix                    9092  0 [[permanent]]
generic                 4356  0 [[permanent]]
ide_core              111280  4 ide_cd,ide_disk,piix,generic
ohci1394               29488  0
ieee1394               85816  2 eth1394,ohci1394
r8169                  26632  0
thermal                13192  0
processor              21952  1 thermal
fan                     4740  0

Debian

  • Peut tu nous donner les messages d erreurs de l'install debian etch ?

a quel moment ca plente ?

  • pas possible de te dire exactement : j'ai 3 pages de texte qui défilent très rapidement puis écran tout noir :

ça ne passe pas à l'install en mode graphique

  • Tu peut essayer de refaire l install sans installer le serveur X , juste une debian de base minimale sans rien pour voir

VGA

  • L'ATI Radeon X600 me semble pas supporté par le driver OpenSource : DRI … au pire tu met vesa si t'as un ecran format 4×3

ça m'étonne vu qu'avec le live CD Etch Gnome ça passe sans problème ?

quel est la resolution de ton LCD ?

pentiumm.txt · Last modified: 2022/04/16 12:23 (external edit)
 
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
Recent changes RSS feed Donate Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki